1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Capacity: 2.8-29mw
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas,liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital

The importance of pH in steam- boiler water - HeatingHelp.com
24 Jun 2014 When we measure pH , we're measuring the power of Hydrogen. to wet steam, which wastes fuel because it robs the steam of its latent heat .

Boiler Water Test | Alkalinity | Ph - Scribd
Internal Waterside Corrosion in. Marine Boilers Waste Heat Boiler Problems Boiler Water Testing . Shell and tube heat exchanger. A Trade Rebound Launches

ISGEC | Waste Heat Recovery Boiler Manufacturers | PH boilers
Isgec offers Waste heat recovery steam pre heater ( PH ) boilers & After Quenching Chamber (AQC) boilers for cement plant exhaust gas. Single drum, Water tube boiler , Natural / Forced circulation. Features of the AQC boilers .

Waste Heat Boiler Preparation - Banks Engineering
Waste Heat Boiler Preparation (Courtesy of Rentech Boiler Systems Inc.) Hydrostatic The following is a recommended procedure for hydrostatic testing : Open the steam .. The key factors responsible for corrosion are water, oxygen, and pH .

Pre- boiler and Boiler Corrosion Control | GE Water
The major problem in low-pressure heating systems is corrosion caused by dissolved oxygen and low pH . Generally, 200-400 ppm P-alkalinity is maintained in the water for effective control of pH . Inhibitor requirements vary depending on the system. Electric boilers are also used for heating.

Corrosion-erosion on waste heat recovery boiler system - CiteSeerX
In a waste heat recovery boiler system, heat of the combustion gases from operating conditions, increasing the testing frequencies should be considered. (magnesium), oxygen, iron and pH should be measured as well (Sandberg et al.,

'Super Boiler ' achieves higher efficiency through the recovery of
1 Jan 2010 An advanced heat recovery system (AHRS) that boosts the Ensuring that real- world commissioning tests are properly executed can benefit FIGURE 1. . ' Super Boiler ' achieves higher efficiency through the recovery of waste heat . How can accurate pH measurement prevent power plant corrosion?

boiler water treatment introduction - The Association of Water
18 Feb 2014 Feedwater. Return. Condensate. Steam. Heat. Exchange. Boiler . Pump The pH of the feed water should be above .. DEHA is controlled based on testing the Feed Water and .. waste heat to the boiler's feed-water or.

Boiler Water Treatment | Sensors for Process Control | Sensorex
26 Oct 2018 pH and conductivity control for boiler feed water is critical. The function of the boiler is to efficiently transfer this heat to the contained water. the steam system ; Eliminating excessive blowdown which wastes water, chemicals, solid levels; Reducing time operators spend testing and adjusting the system.

Inexplicable pH drop in boiler blowdown water - Finishing
In one of the waste heat recovery boilers , (operates at 180 °C), pH of the blow down water drops to 5 and even 4. The feed water is maintained around a pH of 9

Waste Heat - an overview | ScienceDirect Topics
Unfired steam boilers , that is, nominally termed waste heat boilers or heat .. If the test sample is confined within a constant volume, then a swelling pressure will build .. P.H. Groenevelt, in Encyclopedia of Soils in the Environment, 2005

Boilers - an overview | ScienceDirect Topics
An electronic combustion efficiency tester with a data logger to measure stack For example, pre-heating the boiler feed tank to 8090 °C using waste heat can Corrosion may easily develop if the pH of feed water is outside these ranges.

WASTE HEAT BOILER - European Patent Office - EP 3258168 A2
20 Dec 2017 The exhaust gas in the PH boiler has a temperature of 300°C to 400°C, .. [0026] The inventor carries out a test in which exhaust gas from a

High Sulfite Residual - Steam Forum and Power Forum
Your 300-psi Waste Heat Recovery Boiler has twice what I would expect for Sodium Sulfite NaSO3 at ranging 80-ppm to 100-ppm. pH is good

Technical Aspects and Energy Effects of Waste Heat Recovery from
30 Mar 2018 Although the waste heat recovery from furnace slags can be treated as a whole Tests were conducted in different temperatures and solutions: three Other researches are conducted to investigate the effect of pH value on

Water Analyzer WA | Components for steam boilers | Components
Process-oriented monitoring of boiler water and boiler feed water: The water analyzer of exhaust vapour energy; A water analyzer can monitor up to three boilers the measuring modules: pH control for measuring the pH value of the boiler feed Heating boilers · Hot water boilers · Steam boilers · Combined heat and

Boiler Water TreatmentMarine Study
12 May 2015 Prevention of entry into the boiler of foreign matter such as oil, waste , mill-scale, The first stage in the boiler water testing is to collect feed water A sample cooler is a small heat exchanger that uses cold mains Alkalinity test ; PH test ; Chlorides test ; Phosphates test ; Total Hardness test ; Conductivity test

Water_analysis - Lenntech
A boiler requires testing of three different water types as shown below: Make- up, Raw Water, pH , P/M-Alkalinity, Conductivity, Total Hardness, Total Calcium, Total Cooling tower is a heat removal devices used to eliminate waste heat of air