1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas，liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital
Total System Efficiency - An Introduction to Condensing Boilers
In the past, the industry standard for hot water boilers was based on a Figure 3: Example of flue gas condensation temperature based on the hot water return
epsrc thermal management of industrial processes - research.ncl.ac
an extensive literature review of industrial condensing boilers, looking into various .. As the temperature of the flue gas at the exit of a conventional gas fired
Condensing Flue Gases | AERCO
Effective condensing increases the efficiency of the boilers and water heaters by system designs that utilize cooler water temperatures to promote condensing.
Flue Gas Analysis in Industry - Testo 350
generation of steam and hot water for use in process industries .. either as flue gas humidity (at higher temperatures) or as condensate (at lower temperatures).
Protecting Boilers Against Flue Gas Condensation | 2017-08-14
Aug 14, 2017 The North American hydronics industry struggled with this issue for several years This temperature is low enough to cause sustained flue gas
Boiler Efficiency Stack Losses for No.2 Oil | Natural Resources Canada
Aug 27, 2018 For steam boilers the units are lb / h; For high temperature water generators the It is important that measurements of flue gas temperature and
Improving Boiler Room Efficiencies - Federal Corporation
In heavy commercial and industrial boiler applications these efficiencies are . A typical water-tube boiler will have an exhaust temperature of about 550
Understanding Draft | Beckett Corp.
In the oil heating industry, "draft" describes the vacuum, or suction, which Draft volume specifies the cubic feet of gas that a chimney can handle in a given time. Since the outside temperature and flue gas temperature can change, the draft
Boiler systems: Economics and efficiencies - Consulting - Specifying
Jun 19, 2012 System components and configuration, outdoor air temperatures, equipment Condensing boilers work by allowing the flue gas water vapor to
Avoiding Boiler Chimney Corrosion - Forbes Marshall
This chimney corrosion typically happens when the flue gas temperature falls below the dew point of sulphur which enables so2 and so3 to combine with water
Boiler Economizers | CBW Industrial Boiler Waste Heat Recovery
Normally systems burn natural gas, and condensing flue gas environments. The difference is the temperature range in which the economizer is operated.
Industrial Chimney | Thermodyne Boilers
Industrial Chimney Manufacturer Thermodyne Boilers in designing chimney that involves a draft calculation based on flue gas temperature at the inlet and the
Temperature of flue gas out of stack (heat and mass transfer
Enthalpy of air at atm temp and pressure, h3= 298.59775 kJ/kgK. Enthalpy of flue gas What is the temperature of flue gas going out of the chimney? Flue gases . How can I determine the mass flow rate of steam through a boiler? Question.
JC-15D Flue Gas Temperature Monitor || Boiler Controls || Preferred
The JC-15D Flue Gas Temperature Monitor is a microprocessor based According to the Hartford Steam Boiler Inspection and Insurance Co., Three out of
Improving Boiler Efficiency - Energy Depot
Monitoring the flue gas temperature, oxygen content, and carbon dioxide content allows the Condensate from a steam boiler system is hot mineral free water.
Heat Recovery Flue Gas | NaturalGasEfficiency.org
If the process is high temperature and there is a use for steam, then a Heat (Flue Gas Temp) (Water Temp) x (Specific Heat) x (60cfm to hour factor).
condensing boilers - GSA
allowed to escape through the flue. Condensing operating in condensing mode, which requires the temperature of the water returning from point of the water vapor in the flue gas. The dew point is . 2Images courtesy of Harsco Industrial.
High temperature of flue gases - Steam Forum and Power Forum
How increased boiler pressure leads to high flue gas temperature. I know If we increase pressure, maintaining steam flow and superheating
Improved boiler efficiency in just a few steps for large industrial boilers
The efficiency of a boiler is the key indicator of a steam generator and can be The exhaust gas loss decreases as the flue gas temperature at the boiler outlet